Rwandan scientist leads MIT team in creating high-tech toxic gas detectors

Researchers at Massachusetts Institute of Technology (MIT), led by Rwandan professor Aristide Gumyusenge, have developed a detector that could provide continuous monitoring for the presence of toxic gases at home or in industrial settings, at a low cost. The new system combines two existing technologies, bringing them together in a way that preserves the advantages of each while avoiding their limitations. ALSO READ: Is there enough public awareness of indoor pollution in Rwanda? The team used a material called a metal-organic framework, or MOF, which is highly sensitive to tiny traces of gas but whose performance quickly degrades, and combined it with a polymer material that is highly durable and easier to process, but much less sensitive. MOFs are highly porous, have large surface areas, and come in a variety of compositions. Some can be insulators, but the ones used for this work are highly electrically conductive. With their sponge-like form, they are effective at capturing molecules of various gases, and the sizes of their pores can be tailored to make them selective for particular kinds of gases. “If you are using them as a sensor, you can recognise if the gas is there if it has an effect on the resistivity of the MOF,” said Gumyusenge, the paper’s senior author. ALSO READ: Is Rwanda ready to integrate AI into public services? During the development of the sensors, the team had to deal with some challenges including the fact that MOF materials readily become soaked with gases, and then can no longer detect and quantify new inputs. “That’s not what you want. You want to be able to detect and reuse. So, we decided to use a polymer composite to achieve this reversibility,” he noted. The team used a class of conductive polymers that Gumyusenge and his co-workers had previously shown can respond to gases without permanently binding to them. “The polymer, even though it doesn’t have the high surface area that the MOFs do, will at least provide this recognise-and-release type of phenomenon,” he added. They combined the polymers in a liquid solution along with the MOF material in powdered form and deposited the mixture on a substrate, where they dried into a uniform, thin coating. By combining the polymer, with its quick detection capability, and the more sensitive MOFs, in a one-to-one ratio, he said, “Suddenly we get a sensor that has both the high sensitivity we get from the MOF and the reversibility that is enabled by the presence of the polymer.” The material changes its electrical resistance when molecules of the gas are temporarily trapped in the material. These changes in resistance can be continuously monitored by simply attaching an ohmmeter to track the resistance over time. ALSO READ: Five key technologies Rwandans should be ready for in the next five years Gumyusenge and his students demonstrated the composite material’s ability to detect nitrogen dioxide, a toxic gas produced by many kinds of combustion, in a small lab-scale device. After 100 cycles of detection, the material was still maintaining its baseline performance within a margin of about 5 to 10 per cent, demonstrating its long-term use potential. In addition, the material has far greater sensitivity than most presently used detectors for nitrogen dioxide, the team reports. This gas is often detected after the use of stove ovens. And, with this gas recently linked to many asthma cases in the U.S., reliable detection in low concentrations is important. The team demonstrated that this new composite could detect, reversibly, the gas at concentrations as low as two parts per million. ALSO READ: 6 industrial parks under scrutiny for pollution While their demonstration was specifically aimed at nitrogen dioxide, Gumyusenge said, “We can definitely tailor the chemistry to target other volatile molecules,” as long as they are small polar analytes, “which tend to be most of the toxic gases.” Besides being compatible with a simple hand-held detector or a smoke-alarm type of device, one advantage of the material is that the polymer allows it to be deposited as an extremely thin uniform film, unlike regular MOFs, which are generally in an inefficient powder form. Because the films are so thin, there is little material needed and production material costs could be low; the processing methods could be typical of those used for industrial coating processes. “So, maybe the limiting factor will be scaling up the synthesis of the polymers, which we’ve been synthesising in small amounts,” Gumyusenge said. “The next steps will be to evaluate these in real-life settings,” he added.

News

Rwandan scientist leads MIT team in creating high-tech toxic gas detectors